排序方式: 共有36条查询结果,搜索用时 31 毫秒
31.
叶尖射流对风力机叶尖流场影响的数值研究 总被引:1,自引:1,他引:0
为了设计出更加适合非并网系统的风力机,采用在叶尖加入射流的方法来改变叶尖流场分布.在风力机叶片顶端沿弦长布置3个喷口,采用CFD数值模拟方法,通过改变风力机转速获得原型和带喷口的风力机模型的气动特性以及流场分布.发现在转速低于1 200r/min时,带有安装在不同位置的喷口的风力机功率增长率几乎都为零,射流在这一转速范围内对风力机的气动性能几乎没有影响.而转速高于1 200r/min时,随着转速的增大,喷口位于叶尖中部的风力机的功率增长率快速地增大,射流影响了75%以上叶高的表面的压力分布,在大转速下吸力面低压区范围较大,其叶尖涡涡量低于其他方案中,并且在下游扩散得比其他方案快,改善了风力机下游流场,提高了风力机效率.喷口布置在叶尖前缘时其叶尖涡的局部涡量较原型叶片稍大,降低了风力机功率的输出.喷口布置在叶尖尾缘时基本和原型叶片相同.该结论为设计适用于非并网系统的定桨距变转速风力机提供了基础. 相似文献
32.
A triple swirler combustor is considered to be a promising solution for future high temperature rise combustors. The present paper aims to study dilution holes including primary dilution holes and secondary dilution holes on the performance of a triple swirler combustor. Experimental investigations are conducted at different inlet airflow velocities(40–70 m/s) and combustor overall fuel–air ratio with fixed inlet airflow temperature(473 K) and atmospheric pressure. The experimental results show that the ignition is very difficult with specific performance of high ignition fuel–air ratio when the primary dilution holes are located 0.6H(where H is the liner dome height)downstream the dome, while the other four cases have almost the same ignition performance. The position of primary dilution holes has an effect on lean blowout stability and has a large influence on combustion efficiency. The combustion efficiency is the highest when the primary dilution holes are placed 0.9H downstream the dome among the five different locations.For the secondary dilution holes, the pattern factor of Design A is better than that of Design B. 相似文献
33.
34.
35.
侧风条件下短舱进气道地面涡数值模拟 总被引:1,自引:0,他引:1
为了研究起飞状态下进气道地面涡的形成与发展规律,针对缩比的短舱进气道模型进行了3维数值仿真,分析了来流速度和短舱进气道距地面高度对地面涡的影响,得到了地面涡的特点以及对进气道流场品质的影响。研究结果表明:侧风来流速度越低,越容易形成地面涡,随着侧风来流速度的增高,地面涡会消失;短舱进气道距地面高度越低,越容易形成地面涡,地面涡的环量越大;地面涡的形成会增大进气道出口截面的流场畸变程度,短舱进气道距地面高度对畸变的影响很小,畸变主要受侧风来流速度的影响。最后给出了侧风条件下地面涡的分界线方程,可作为是否存在地面涡的判断依据。 相似文献
36.
以TC4合金层板结构的超塑性成形过程为研究对象,采用有限元软件MARC模拟计算了TC4合金宽弦空心夹芯结构的超塑性成形过程。分别分析了应变速率敏感指数、目标应变速率及扩散连接宽度等参数对贴模过程及壁板厚度分布的影响。结果表明:当应变速率敏感指数较大时,夹芯结构会发生沿纵向挤出延伸变形;当目标应变速率为10-3时,材料表现出较佳的超塑性性能;而扩散连接宽度的大小对超塑性成形后板材壁厚分布的均匀性有一定影响。通过控制最大应变速率的方法,提取出了最优化的压力时间曲线。研究结论可为钛合金空心夹芯结构件的超塑性成形提供理论参考。 相似文献